Search results for "Electrolytic capacitor"

The Effect of Anodizing Bath Composition on the Electronic Properties of Anodic Ta-Nb Mixed Oxides

2022

Anodic oxides were grown to 50 V on Ta-Nb sputtering deposited alloys, with high Nb content, in acetate ions containing an aqueous solution to study the effect of the anodizing bath composition on anodic layers’ dielectric properties. Photoelectrochemical measurements proved the presence of a photocurrent in the band gap of photon energy lower than oxides, due to optical transitions involving localized electronic states as a consequence of acetate ions incorporation. Flat band potential value estimates assessed the insulating nature of the anodic oxides grown in the acetate buffer solution. Differential capacitance measurements showed that the highest capacitance value was measured for the …

Polymer Selection and Cell Design for Electric-Vehicle Supercapacitors

2000

Supercapacitors are devices for applications requiring high operating power levels, such as secondary power sources in electric vehicles (EVs) to provide peak power for acceleration and hill climbing. While electronically conducting polymers yield different redox supercapacitor configurations, devices with the n-doped polymer as the negative electrode and the p-doped polymer as the positive one are the most promising for EV applications. Indeed, this type of supercapacitor has a high operating potential, is able to deliver all the doping charge and, when charged, has both electrodes in the conducting (p- and n-doped) states. This study reports selection criteria for polymer materials and ce…

Anodization and anodic oxides

2018

Anodizing is a low-temperature, low-cost electrochemical process allowing for the growth, on the surface of valve metals and valve metal alloys, of anodic oxides of tunable composition and properties. This article is an overview on theoretical aspects concerning the general aspects of the kinetics of growth of barrier and porous anodic oxides and some of their present and possibly future technological applications of anodic oxides. The first part of the article is devoted to anodic oxide growth models, from Guntherschulze and Betz work (in 1934) to the more recent results on barrier and porous oxide films. The second part is focused on industrial processes to fabricate anodic oxides and the…

Modelling, simulation and characterization of a supercapacitor

2020

In the last decade, the issue of air pollution or the reduction of CO2 emissions has become of extreme interest both for civil society and then for the industrial and scientific research world. For this reason, the scientific research on automotive is called to answer with increasingly innovative solutions. One of the principal subjects are the storage and the utilization of the electric energy for electrical and hybrid vehicles. Nowadays, supercapacitors are getting more and more attention because of their characteristics that allow them to be a bridge between electrolytic capacitors and batteries in several application such as bust-mode energy delivery, regenerative breaks and so on. The …

ELECTROCHEMICAL FABRICATION OF METAL/OXIDE/CONDUCTING POLYMER JUNCTIONS FOR ELECTRONIC DEVICES

2014

Adaptive tuning system and parameter estimation of a digitally controlled boost converter with STM32

2019

. This paper proposes a diagnostic system of a power electronic converter, based on a cheap STM32 Nucleo board, aiming to extract some relevant measurements which gives back important values of the converter's parameters behavior. Moreover the designed system is also exploited for implementing the converter's auto tuning in order to optimize its dynamic performance.

Physico-chemical Characterization of Aluminium Oxide Films Grown on Etched Foils for Electrolytic Capacitors

2012

The effect of hydration layers on the anodic growth and on the dielectric properties of Al2O3 for electrolytic capacitors

2014

Hydrous films were grown on high purity and cubicity Al foils for electrolytic capacitors in deionized water, ethylene glycol - deionized water and in glycerol - deionized water for different immersion times. According to the X-ray diffraction patterns the hydration treatment allowed to grow a pseudo boehmite layer on Al surface whose morphology is appreciably affected by the bath composition. Capacitance measurements and photoelectrochemical findings suggest that a more compact barrier layer forms during the immersion in alcohol containing solutions. The hydration in water allowed to save energy and to prepare more blocking oxide films. The beneficial effect of hydration in hot water on th…